How To Replace Front Camera On Samsung J8

Introduction

Utilise this guide to remove or replace the front end-facing camera assembly in your Samsung Galaxy S8.

This guide involves removing the rear glass embrace, you will need replacement agglutinative to reattach the back cover to the phone.

Earlier disassembling your telephone, belch the bombardment below 25%. The bombardment can catch burn and/or explode if accidentally punctured, simply the chances of that happening are much lower if discharged.

• We recommend that you lot make clean your microwave before proceeding, equally any nasty gunk on the bottom may end upwardly stuck to the iOpener.

• Place the iOpener in the eye of the microwave.

• For carousel microwaves: Make certain the plate spins freely. If your iOpener gets stuck, it may overheat and burn.



• Heat the iOpener for thirty seconds.

• Throughout the repair procedure, as the iOpener cools, reheat it in the microwave for an additional thirty seconds at a fourth dimension.

• Be careful not to overheat the iOpener during the repair. Overheating may cause the iOpener to burst.

• Never impact the iOpener if it appears bloated.

• If the iOpener is still too hot in the centre to touch on, continue using it while waiting for it to cool down some more before reheating. A properly heated iOpener should stay warm for upwardly to 10 minutes.

• Remove the iOpener from the microwave, property information technology by 1 of the two flat ends to avert the hot center.

• The iOpener will exist very hot, and then be careful when handling information technology. Use an oven mitt if necessary.

• If you don't take a microwave, follow this step to heat your iOpener in boiling h2o.

• Fill a pot or pan with enough h2o to fully submerge an iOpener.

• Heat the water to a boil. Turn off the heat.

• Place an iOpener into the hot water for 2-3 minutes. Make certain the iOpener is fully submerged in the water.

• Utilise tongs to extract the heated iOpener from the hot water.

• Thoroughly dry the iOpener with a towel.

• The iOpener will exist very hot, so exist careful to hold it only by the finish tabs.

• Your iOpener is ready for utilise! If you demand to reheat the iOpener, estrus the water to a boil, turn off the heat, and place the iOpener in the h2o for two-3 minutes.

• Opening your phone will compromise its waterproof seals. Accept replacement adhesive prepare earlier you proceed, or take intendance to avoid liquid exposure if you reassemble your telephone without replacing the adhesive.

• Oestrus an iOpener and employ it to a long edge of the S8 for about 2 minutes.

• Y'all may need to reheat and reapply the iOpener several times to become the phone warm enough. Follow the iOpener instructions to avoid overheating.

• A pilus dryer, heat gun, or hot plate may also be used, but be careful non to overheat the phone—the OLED display and internal battery are both susceptible to heat damage.

• Every bit you're waiting for the agglutinative to soften, move on and read the following step to go an idea of where to pry.

• In the following steps you lot will be cutting through the adhesive around the border of the rear glass panel.

• The agglutinative on the rear case is laid out as seen in the first prototype.

• The prying pattern as seen from the outside of the phone is as follows:

• Thick portions of adhesive

• Thin areas of adhesive

• Avert prying here, to protect the fingerprint sensor.

• Once the back panel is warm to the affect, use a suction cup as close to the heated edge of the phone as you lot can while avoiding the curved edge.

• The suction cup will non make a good seal on the curved portion of the glass.

• If the phone'southward back cover is cracked, the suction cup may non stick. Try lifting it with stiff tape, or superglue the suction cup in place and allow it to cure so y'all can proceed.

• Lift on the suction loving cup, and insert an opening pick nether the rear drinking glass.

• Due to the curved glass, yous will be pushing up, rather than inserting parallel to the aeroplane of the phone.

• Once yous have the tool firmly inserted into the drinking glass, reheat and reapply the iOpener to soften the agglutinative.

• Slide the opening pick downwards the side of the telephone, separating the adhesive.

• Go slowly so that the tool doesn't sideslip out of the seam. If cut becomes difficult, reheat and reapply the iOpener.

• Echo the previous heating and cutting procedure for the remaining 3 sides of the phone.

• Exit an opening pick on each side equally yous go on to the side by side to prevent the adhesive from resealing.

• The fingerprint sensor cable connects the phone to the rear glass near the main camera. The cablevision is very brusk and should disconnect as the rear glass is removed.

• As y'all lift the glass, peek in to be sure the orange cable with a blue connector has disconnected.

• Use the opening picks to slice through any remaining agglutinative and open the phone slightly.

• If the fingerprint sensor cable seems snagged or stays taut exercise non open up the telephone any farther. Disconnect the connector with the betoken of a spudger before proceeding.

• During reassembly, in lodge to reconnect the fingerprint sensor cable, first angle the back encompass into position until the cable connector lines up perfectly over its socket. Then, use the flat end of your spudger to gently snap the connector into place by pressing it straight down.

• Remove the drinking glass from the phone.

• To install a new back cover:

• Utilise tweezers to skin abroad whatever remaining agglutinative from the phone's chassis. And so clean the adhesion areas with high concentration isopropyl booze (at least 90%) and a lint-free cloth to prep the surface for the new adhesive.

• Peel the adhesive bankroll off of the new rear glass, carefully line up one edge of the drinking glass against the phone chassis, and firmly press the glass onto the phone.

• Follow this guide to reinstall the old back encompass, or to install a back cover without pre-installed adhesive.

• Exist sure to turn on your phone and test your repair before installing new agglutinative and resealing the phone.

• If desired, you may reinstall the back cover without replacing the adhesive. Remove whatever large chunks of adhesive that might foreclose the back cover from sitting down flush. Afterwards installation, heat the dorsum comprehend and apply force per unit area to secure it. It won't exist waterproof, but the glue is usually more than stiff plenty to hold.

• You may besides need to transfer the camera bezel to your new office. If that'due south the case, follow our camera bezel replacement guide.

• Remove eleven iii.vii mm screws using a Phillips #000 screwdriver.

• Remove the NFC antenna and charging roll assembly.

• Remove 3 3.vii mm Phillips #000 screws.

• Remove the loudspeaker assembly.

• Use the flat finish of a spudger to disconnect the bombardment connector.

• Although the battery is not shown in the adjacent steps, at that place is no need to remove it for this guide. Merely disconnect the battery and you're good to become.

• Use tweezers to gently elevator the front-facing camera module out of its slot.

• Although the motherboard is not shown in the photo, it is not necessary to remove the motherboard to remove the camera module.

Decision

After reapplying adhesive, follow these instructions in reverse order to reassemble your device.

Team

Embed this guide

Cull a size and copy the code below to embed this guide equally a pocket-sized widget on your site / forum.

Preview

Source: https://www.ifixit.com/Guide/Samsung+Galaxy+S8+Front-Facing+Camera+Replacement/90352

Posted by: valenzuelacountim.blogspot.com

Share this post